Logger Script Contact smart cards tester : MP300 TC3 - Micropross ::NUBICOM::
New Products

MP300 TC3 접촉식 스마트 카드 테스터

  • 개요
  • 기술 자료
  • 사용 분야
  • 솔루션
  • 액세사리

High end tester, for contact smartcards and contact based secure elements. Support of ISO 7816, SWP/HCI, USB 2.0, USB-IC and I2C protocols. Immense flexibility in terms of physical and protocol parameters. Tester certified by EMVCo for L1 type approval, and by the GCF/PTCRB for SWP. The MP300 TC3 is the worldwide reference for test of contact smart cards and secure elements. Shipped to hundreds of units worldwide, its numerous test features make this tool the ideal companion for characterisation of components, and type approval at validation laboratories. The MP300 TC3 main features are :

주요 특징 :

  • Terminal simulation following the ISO 7816, SWP/HCI, I2C, SPI, USB 2.0, USB-IC protocols
  • Able to test ID-1 smart cards, SIM and U-SIM components, eSIM as well as M2M modules
  • Fully compatible with the requirement of the ISO 7816 (ISO 10373-3) test specification
  • Completely supports the ETSI TS 102 613 and TS 102 622 specifications
  • Records the communication between itself, and the device under test, and offers a graphical display of the spied data
  • External spy mode also available
  • Very deep possibilities of customisation of physical and protocol parameters
  • Numerous measurement features and test implemented : current, voltage, open/short, capacitance, ...
  • Reference tester for numerous test standards : EMVCo L1 electrical and protocol, ISO 7816-3, ETSI TS 102 613 and TS 102 622

데이터시트 다운로드

기술 자료

지원되는 프로토콜
ISO/IEC 7816-3
- T=0 and T=1 protocols : 100% implemented, managed by Firmware and FPGA, accelerated by hardware

SWP/HCI (ETSI TS 102.613 and ETSI TS 102.622)
- SWP transmission : Assisted by hardware
- LLC layers support : ACT, CLT, S-HDLC realised by firmware

-Available speeds : Low speed, full speed
-Classes : ISO/IEC 7816-12, mass storage, custom protocols

modes supported :
-Standard mode
-Fast mode
-Fast mode plus
-Supports clock stretching, multi master arbitration, anti tearing
-Programmable parameters :
+Setup time, hold time, start and stop condition
+Clock high and low states
+Address width (7 and 10 bits)
+Nack condition

-Data width : 8 bits
-programmable parameters :
+phase, polarity
+anti tearing

Synchronous chips
-Support of all kind of memory components (SLE 46xx, T2G, …)Raw mode
-Implementation of custom protocols and support of out of standard chips

프로그래밍 가능한 파라미터
물리적 파라미터
- Vcc : 0V ~ 10V 조정 가능
- Vol/Voh :
- 0V ~ 5V / 1V ~ 7V
- 모든 핀은 독립적으로 조정 가능
- Vil/Vih :
- 0.2V ~ 5V / 1V ~ 6.8V
클럭 (Clock) 주파수
-ISO 7816 clock :
+Adjustable from 10kHz to 10Mhz
+Duty cycle : can be adjusted from 30% to 70%
-SPI clock :
-Adjustable up to 25MHz
-Pin states
+All pins can be managed separately

ISO 7816 통신 파라미터
-Adjustable parameters : All normative timings (WWT, BWT, CWT, …), parity, pull-up resistor

SWP 통신 파라미터
사용 가능한 전송속도 :
- 49kbps ~ 1,9Mbps 모든 전송 속도
- 0% ~ 50% 조정 가능한 SWP 듀티 사이클
- 조정 가능한 매개 변수 : 활성화 시간, P2, P3 파라미터, 전류 감지 레벨

USB-IC 파라미터
- 지원되는 전압 클래스 : 1.8V 및 3.0V
스파이(SPY) 기능
정확도 : 20 ns
신호 표시 :
- 모든 8개의 핀(C1 C2 C3 C4 C6 C7 C8)
- SWP S1, S2
- 바이트(Bytes)
- 프레임(Frames)
- 트리거(Trigger) 상태
I2C start and stop conditions, ACK/NACK, SDA/SCL transitions
SPI SCK, MOSI, LISO, SS transitions
Analog information (current, voltage measurement)

사용 가능한 테스트
전기 테스트
– Open/short test (on all contacts,current forced can be adjusted)
– Leakage current (all contacts)
– Voltage measurement (all contacts, static, dynamic, burst mode)
– Current measurement (all contacts, static, dynamic, burst mode)
– Parametric tests (V=f(I), I=f(V))
– SWP specific measurement (statistics on SWP S2 current values)

논리적 테스트
- Anti tearing (checks the chip’s integrity against accidental removing from the reader)
– All timing measurement
– ISO 7816 and SWP concurrent I/O testing : send frames in ISO and SWP simultaneously

사용 분야

MP300 TC3은 일반적으로 다음과 같은 분야에서 사용됩니다 :

  • 접촉식 스마트카드 OS의 디버그
  • EMVCo 및 SWP/HCI 규격에 따는 형식 승인
  • 접점 구성요소의 특성화
  • 품질 검사
  • 가족친화우수기업
  • 청년친화 강소시업
사업자등록번호 : 220-86-72761대표이사 : 신동만대표전화 : 070-7872-0701팩스 : 02-2167-3801
(우)07299 서울특별시 영등포구 경인로 775 (문래동 3가, 에이스하이테크시티 3동 2층)